High Technical Explosion proof Equipment Laboratory
IRANATEX
پیشرفته ترین آ زمایشگاه تست تجهیزات ضد انفجار در خاورمیانه
CERTIFICATE Laboratory Na :irn1026
از آنجائی که تولیدات یک کارخانه سازنده سیستم های ضد انفجار Explosion proof Systems طبق ATEX Directive94/9/EC میباشد لازم است گواهینامه های EC Type Examination و QAN (Quailty Assurance Notification )n که اولی به عنوان گواهینامه اصلی دستگاههای ضد انفجار و دومی به عنوان گواهینامه مکمل آن است Approved Notification Body نیز اخذ شود تا شرایط تولید یک دستگاه ضد انفجار حاصل گرددو اگر قرار باشد مطابق استاندارد IEC باشد لازم است گواهینامه های CoC ((Certification of Conformity )) به عنوان گواهینامه اصلی و QAR ((Quality Assessment Report)) به عنوان مکمل آن از EX Certifide Bodyاخذ شود. در گواهینامه اصلی آزمایش سیستم های ضد انفجار از سری استانداردهای IEC 60079 بنا بر ضرورت و نوع دستگاه ((که حداقل مربوط به سال 2006 و یا جدیدتر باشد.))
آزمایشگاه تخصصی IRANATEX پیشرو در ارائه خدمات مهندسی و آزمون قطعات و تجهیزات وابسته به کارخانه ایران کولر تنها و پیشرفته ترین آزمایشگاه تخریبی تست تجهیزات ضد انفجار در منطقه میباشد که مطابق با استانداردهای IEC عمل می نماید. این مرکز دارای سرتیفیکیت IsoIEC17025:2005 بوده که TEST REPORTS (گزارشات تست)) صادره برای سازمان های ارائه دهنده ATEX اروپائی قابل قبول میباشد.
Explosion Test Laboratory
According to international standards, electrical and non-electrical equipment installed in hazardous areas need to prove their enhanced capability of withstanding special external events. Therefore special laboratories capable of simulate such extreme conditions are required. To this extent IRANATEX Group offers a wide range of testing services, on electrical and non-Electrical equipment used in hazardous areas:
- Tests in explosive mixture (Explosion proof and Flameproof tests)
- Impact tests
- Static overpressure tests
- Ex-i spark ignition tests
- Ingress Protection Tests (IP code)
- Environmental Exposure Tests
- Thermal Tests
- Dimensional Checks
- Non-Electrical Product Tests
Test & Standards
| Standards | Tests |
| EN/IEC 60079-0 | Equipment - General requirements |
| EN/IEC 60079-1 | Equipment protection by flameproof enclosures 'd' |
| EN/IEC 60079-2 | Equipment protection by pressurized enclosures 'p' |
| EN/IEC 60079-5 | Equipment protection by powder filling 'q' |
| EN/IEC 60079-6 | Equipment protection by oil immersion 'o' |
| EN/IEC 60079-7 | Equipment protection by increased safety 'i' |
| EN/IEC 60079-11 | Equipment protection by intrinsic safety 'i' |
| EN/IEC 60079-13 | Equipment protection by pressurized room 'p' |
| EN/IEC 60079-15 | Equipment protection by type of protection 'n' |
| EN/IEC 60079-25 | Intrinsically safe systems |
| EN/IEC 60079-26 | Equipment with equipment protection level (EPL) Ga |
| EN/IEC 60079-27 | Fieldbus intrinsically safe concept (FISCO) |
| EN/IEC 60079-31 | Equipment dust ignition protection by enclosure 't' |
| EN/IEC 60529 | Ingress Proectuin (IP) Tests |
اولین مرحله تست در آزمایشگاه IRANATEX تست میکروسکپی توسط متخصصین بسیار کارآمد با پیشرفته ترین میکروسکپ ها میباشد
تست ضربه به منظور بررسی مقاومت و استحکام قطعه
IMPACT TEST
کابین تست باران
Rain Chamber test
| Rating | Protection from Solids | Protection from Liquids |
|---|---|---|
| IP00 | No protection | No protection |
| IP01 | No protection | condensation |
| IP02 | No protection | water spray < 15 degrees from vertical |
| IP03 | No protection | water spray < 60 degrees from vertical |
| IP04 | No protection | water spray from any direction |
| IP05 | No protection | low pressure water jets from any direction |
| IP06 | No protection | high pressure water jets from any direction |
| IP07 | No protection | immersion between 15cm and 1m depth |
| IP08 | No protection | long term immersion to a specified pressure |
| IP10 | touch by hands (>50mm) | No protection |
| IP11 | touch by hands (>50mm) | condensation |
| IP12 | touch by hands (>50mm) | water spray < 15 degrees from vertical |
| IP13 | touch by hands (>50mm) | water spray < 60 degrees from vertical |
| IP14 | touch by hands (>50mm) | water spray from any direction |
| IP15 | touch by hands (>50mm) | low pressure water jets from any direction |
| IP16 | touch by hands (>50mm) | high pressure water jets from any direction |
| IP17 | touch by hands (>50mm) | immersion between 15cm and 1m depth |
| IP18 | touch by hands (>50mm) | long term immersion to a specified pressure |
| IP20 | touch by fingers (>12mm) | No protection |
| IP21 | touch by fingers (>12mm) | condensation |
| IP22 | touch by fingers (>12mm) | water spray < 15 degrees from vertical |
| IP23 | touch by fingers (>12mm) | water spray < 60 degrees from vertical |
| IP24 | touch by fingers (>12mm) | water spray from any direction |
| IP25 | touch by fingers (>12mm) | low pressure water jets from any direction |
| IP26 | touch by fingers (>12mm) | high pressure water jets from any direction |
| IP27 | touch by fingers (>12mm) | immersion between 15cm and 1m depth |
| IP28 | touch by fingers (>12mm) | long term immersion to a specified pressure |
| Rating | Protection from Solids | Protection from Liquids |
|---|---|---|
| IP30 | tools & wires (>2.5mm) | No protection |
| IP31 | tools & wires (>2.5mm) | condensation |
| IP32 | tools & wires (>2.5mm) | water spray < 15 degrees from vertical |
| IP33 | tools & wires (>2.5mm) | water spray < 60 degrees from vertical |
| IP34 | tools & wires (>2.5mm) | water spray from any direction |
| IP35 | tools & wires (>2.5mm) | low pressure water jets from any direction |
| IP36 | tools & wires (>2.5mm) | high pressure water jets from any direction |
| IP37 | tools & wires (>2.5mm) | immersion between 15cm and 1m depth |
| IP38 | tools & wires (>2.5mm) | long term immersion to a specified pressure |
| IP40 | tools & small wires (>1mm) | No protection |
| IP41 | tools & small wires (>1mm) | condensation |
| IP42 | tools & small wires (>1mm) | water spray < 15 degrees from vertical |
| IP43 | tools & small wires (>1mm) | water spray < 60 degrees from vertical |
| IP44 | tools & small wires (>1mm) | water spray from any direction |
| IP45 | tools & small wires (>1mm) | low pressure water jets from any direction |
| IP46 | tools & small wires (>1mm) | high pressure water jets from any direction |
| IP47 | tools & small wires (>1mm) | immersion between 15cm and 1m depth |
| IP48 | tools & small wires (>1mm) | long term immersion to a specified pressure |
| Rating | Protection from Solids | Protection from Liquids |
|---|---|---|
| IP50 | Limited dust ingress protection | No protection |
| IP51 | Limited dust ingress protection | condensation |
| IP52 | Limited dust ingress protection | water spray < 15 degrees from vertical |
| IP53 | Limited dust ingress protection | water spray < 60 degrees from vertical |
| IP54 | Limited dust ingress protection | water spray from any direction |
| IP55 | Limited dust ingress protection | low pressure water jets from any direction |
| IP56 | Limited dust ingress protection | high pressure water jets from any direction |
| IP57 | Limited dust ingress protection | immersion between 15cm and 1m depth |
| IP58 | Limited dust ingress protection | long term immersion to a specified pressure |
| IP60 | Total dust ingress protection | No protection |
| IP61 | Total dust ingress protection | condensation |
| IP62 | Total dust ingress protection | water spray < 15 degrees from vertical |
| IP63 | Total dust ingress protection | water spray < 60 degrees from vertical |
| IP64 | Total dust ingress protection | water spray from any direction |
| IP65 | Total dust ingress protection | low pressure water jets from any direction |
| IP66 | Total dust ingress protection | high pressure water jets from any direction |
| IP67 | Total dust ingress protection | immersion between 15cm and 1m depth |
| IP68 | Total dust ingress protection | long term immersion to a specified pressure |
| IP69K | Total dust ingress protection | steam jet cleaning |
Test vibrating table
THE ELECTRICAL LEAKAGE TEST
تست شیشه های ضد انفجار توسط آزمایشگاه اIRANATEX
این آزمایش بر اساس استاندارد EN13541 انجام پذیرفته است
مراحل ارزیابی تجهیزات شامل :
4-THERMAL LEAK TEST
5-MICROSCOPIC EXAMINATION (( Microstructure studies))
6-VIBRATION TEST
7- BOMB CHAMBER
8-SIMULATION TEST EXPLOSION
These are very widely used in characterizing the material. Various phases in an alloy system are
quantified and the extents of their presence are correlated to the properties like strength, corrosion
resistance, stability of the material, etc.
The micro structure reveals the grain structure whether as cast, wrought, heat treated or subjected
to any special treatment such as carburizing, hardening etc.
This also reveals the presence of carbides particularly Chromium carbide which is a matter of concern
in high chromium, nickel alloys.
Highly experienced and qualified metallurgists enable ELCA to deliver the metallurgical condition of
any metal, including exotic ones. The application knowledge of our technicians enable us to give you
all the required characteristics, thus enabling the customer in making proper decisions while using the
material.
The image analysis system incorporated into our high power metallurgical microscopes enables ELCA
to deliver accurate and useful images of metallurgical structures.
Tests we cover:
- Micro Examination with Photographs
- Micro Examination for Welded Pipes
- Macro Examination for Forgings, Mockups, Fillet Weld, Grain Flow
- Macro Examination for Pipes
- Step Down Test
- Weld Penetration Test with measurements and photographs
- Mercurous Nitrate Test
- Inclusion Rating
- IS 4163 / ASTM E-45 Method A
- Method D as per ASTM E-45
- DIN 50602 K3 Method
- DIN 50602 K4 Method
- By Microscopic Method
- By Micro Hardness Traverse Method
- Case Depth
- By Microscopic Method
- By Micro Hardness Traverse Method
- Surface Roughness
